Rear end identification ford.

The rear end and transmission information are also included in valuable option codes, located on the truck safety compliance certification label in the door pillar. If, for some reason, these codes have faded, been removed, or become unreadable in any way, take your F150 to your local Ford dealer to try and get more information as to how to identify …16 Nov 2005 ... I found a little more info on the net. Seems that the Dana 80 has 10 diff cover bolts. The Ford 10.25" has 12 diff cover bolts, which is what ...A little more detail: If the codes on the rear differential tag were: S409B. 3L73 102 8C11. The break-down of these codes would be: S409B: S = Sterling Differential. 409 = Print Number (Model Number) B = Revision Identifier (Change in Design)The axle code can typically be found on the vehicle’s door tag, which is located on the driver’s side door jamb. It may also be stamped on the axle housing itself or listed on the vehicle’s build sheet. The chart provides a handy reference for decoding the axle code once it has been located. See also Fixing Transmission & Solenoid for ...Ford Rear Axle Assembly Identification - Page 17. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.

Pinion Yoke and ABS Plug. 8) These rearends generally use a 28-spline pinion yoke, but some trucks use a 30-spline. 9) This is the plug for ABS found on some 8.8s. Advertisement. The Ford 8.8...It's easy to understand Ford rear-axle identification. Five basic types have been used in Fords, Mercurys, and Lincolns since 1957. Here's how it plays out. See All …

Rear Axle Ratio Charts For 1967 - 1972 GM Trucks The 1967 - 1972 Chevrolet & GMC Pickups Message Board . Register or Log In To remove these advertisements. The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message …The Mustang came from the factory with a 7.5-inch or 8.8-inch rear end, after 1979, with a variety of gear ratios and in both limited slip and open differential configurations. Decoding the data tag on the rear end will provide the information required when ordering replacement or up-graded parts for the Ford differential inside the rear end ...

Ford Rear Axle Assembly Identification - Page 07. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or L. Axle.ID Tags: The Ford 8.8 differential ID tag attached to the differential will tell you the gear ratio, rear end style, and whether it has limited-slip. Also on the tag is an ID number, which, until 1985, included four to five letters and no numbers. Almost all 8.8s – and all post-’86 Ford rear ends – have letters and numbers. You are here: Home Tech Articles Front / Rear Differentials Ford Rear Axle Identification - Page 02. ‹ Back to Technical Index. Ford Rear Axle Assembly Identification - Page 02. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L. Axle Shaft Splines. Differential Identification Work Page. Accurate Differential Identification is the first and most important step in your differential repair, upgrade or overhaul project. The following information is provided to help you identify the differential you are working on. If in doubt, consult one of our differential experts at (800)510-0950! When it comes to getting power to the pavement, GM's 10-bolt, 8.5-inch rear end with Positraction is a hero. Like Superman in street clothes, however, it can be hard to identify this beefy unit among its weaker cousins, the 10-bolt, 8.2-inch with open differential. GM built countless thousands of both types of 10-bolts from 1970 to 1994.

Step 4. Locate the identification tag on Ford manufactured rear end units. According to Fordification.com, the tag is located on the driver's side of the unit, mounted vertically, facing the front of the vehicle. The top line of the tag is the axle model and may consist of letters only, or a combination of both letters and numbers.

The 1940s Classic Ford Cars Channel covers popular antique Fords from the decade. Take a look under the hood of 1940s classic Ford cars. Advertisement The 1940s Classic Ford Cars C...

Ford Rear Axle Assembly Identification - Page 17. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.Differential Identification Work Page. Accurate Differential Identification is the first and most important step in your differential repair, upgrade or overhaul project. The following information is provided to help you identify the differential you are working on. If in doubt, consult one of our differential experts at (800)510-0950!The simplest way to identify the rear axle assembly of a Ford vehicle is to look at the plate stamped on the component. The plate provides important information about the axle asse...Early Ford Beam Axle Identification and Dimensions; How To Box-In a Differential / Solid Axle Rear-End Housing; How To Decode Ford Part Numbers; How To Install a Limited Slip/Posi Unit in a GM 10 Bolt 8.5″ Rear-end; How To Install Ring and Pinion Gears in a Ford 8.8 Rear-End; How To Narrow a Ford 8.8 Inch RearendPinion Yoke and ABS Plug. 8) These rearends generally use a 28-spline pinion yoke, but some trucks use a 30-spline. 9) This is the plug for ABS found on some 8.8s. Advertisement. The Ford 8.8...Ford F150 Forum. The site for Ford truck owners, by Ford truck owners. Skip to content. Quick links. FAQ; F150 Forum . Ford F-150 / F-Series Generations. 2004 - 2008 Ford F-150. Looking for recent topics? F-150 REAR END ID TAG. 2 posts • Page 1 of 1. eddinstd New Member Posts: 1 Joined: Sun Dec 02, 2007 4:04 am. F-150 REAR END …Ford Aerostar – The Ford Aerostar 8.8-Inch axles had 28-spline shafts. NOTE: Increasing from a 28-spline to a 31-spline axle allegedly increases strength of the axle shaft by 34%, however I’ll go by the capacity ratings of the axle assemblies provided by the manufacturer. Ford Rates the Ranger axle at 2750 lbs and the Explorer axle at 3200 lbs this is a 16% …

Dec 25, 2023 · The code can be found on the Vehicle Identification Number (VIN) label, which is typically located on the driver’s side door jamb or the front windshield. 2. Decoding the Axle Code. To decode the Ford Axle Code, you need to refer to the manufacturer’s specifications or consult an online decoding tool. The code is made up of several ... XJ. bobl1 (Bob L) July 14, 2022, 12:24pm 1. Hi I’m a brand new member. I had a 72 SJ Sedan that i bought for parts (very badly rusted). I took the rear out and the tag said “75” and there was yellow crayon marking on the top of the rear housing with two indistinguishable letters and an OK I’m thinking it is indeed a 75 that replaced the ...Early Ford Beam Axle Identification and Dimensions; How To Box-In a Differential / Solid Axle Rear-End Housing; How To Decode Ford Part Numbers; How To Install a Limited Slip/Posi Unit in a GM 10 Bolt 8.5″ Rear-end; How To Install Ring and Pinion Gears in a Ford 8.8 Rear-End; How To Narrow a Ford 8.8 Inch RearendFord assigned dozens of transmission identification codes to its 1973 through 1979 trucks and vans, including F100 through F350 trucks and E100 through E300 vans, and trucks in the...The Dana 44 differential cover will measure about 9 1/2 inches wide and 10 1/2 inches tall, while the Dana 60 differential cover will measure about 11 1/4 inches wide and 12 inches tall. Beware ...

Ford 7.5-Inch and 8.8-Inch Axle Visual Identification: Both axles use (10) bolts to hold on the cover, but there is an obvious difference in their shape. Ford 7.5-Inch rear axle above – Ford 8.8-Inch rear axle below.

Ford Rear Axle Assembly Identification - Page 01. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.Ford 7.5-Inch rear axle above – Ford 8.8-Inch rear axle below. Identification From Axle Tag: The axle tag is bolted to the rear differential cover, and is held on with one of the cover bolts. From the example above, you can see that the lower line shows the gear ratio, and axle diameter. So from that example, we can see that the tag above is a 7.5 inch axle …D0TA-AS: Dana 60 / 3.73-1 / non Limited Slip / 5200 lb. Rear Axle Capacity / Rear Axle Parts List # 93. Decoded from the 1964/72 Ford Truck Parts Catalog / Differential Carrier & Axle ID Chart / Section 40.3 / Page 6. I can decode any Ford axle tag, car or truck, from 1948 thru 2002.Depending on the model, you can typically find it on the driver’s side door jamb, the glove compartment, or in the owner’s manual. Additionally, there are online …Dec 28, 2023 · Component 1: Axle Ratio. The axle ratio is the numerical representation of the gear ratio, which expresses the number of revolutions the driveshaft makes for each revolution of the axle. It determines the vehicle’s torque, towing capacity, and fuel efficiency. Common axle ratios found in Ford vehicles include 3.31, 3.55, 3.73, and 4.10. 1113 posts · Joined 2006. #2 · Jan 31, 2010. You have an 8.8.You could swap in a ford 9''.Just make sure you get one with the same gear ratio as your old one so it matches the front.The most common ratio was 3.55 for a 8.8 and 3.50 for a 9'' in a Bronco.An axle from a f150 would bolt in as well. Custom front and rear bumpers.You are here: Home Tech Articles Front / Rear Differentials Ford Rear Axle Identification - Page 12. ‹ Back to Technical Index. Ford Rear Axle Assembly Identification - Page 12. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L. Axle Shaft Splines.

The rear end and transmission information are also included in valuable option codes, located on the truck safety compliance certification label in the door pillar. If, for some reason, these codes have faded, been removed, or become unreadable in any way, take your F150 to your local Ford dealer to try and get more information as to how to identify …

The Chevy’s rear axle code contains information on the vehicle’s gear ratio, date of manufacture and the rear axle assembly plant. The prefix on the code consists of two letters fo...

A Chevy 1/2 ton pick-up may have a Chevy 10 bolt rear axle or a 12 bolt rear axle. Both of these are semi-floating axles. A Chevy 3/4 ton pick-up may have a 14 bolt semi-float rear axle or a 14 bolt full-floating axle. All of these axles take different parts so we need to properly identify the axle you have to get you the right part.Contact. You are here: Home Tech Articles Front / Rear Differentials Ford Rear Axle Identification - Page 15. ‹ Back to Technical Index. Ford Rear Axle Assembly Identification - Page 15. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L.See All 52 Photos. Detailing a rear axle is a major part of a Mustang concours restoration, right up there with the engine and the front suspension in complexity. There are so many parts, colors ...The third character is for the vehicle model code. For example, R3 is Mustang, H7 is F-Series Short Cab, L3 is F150/250. So a 2011 Mustang axle is part number BR3W-4001-KH. The last character designates which Design Engineering Office is responsible for the component. There is a fair amount of detailed information contained within the part ...In this video, we measure up the housing ends on our project housing. TWO RULES TO FOLLOW!1 - Take the Measurements! DO NOT go by appearance. 2 - Have a pla...1928-1931 Model A axles have a uniform curve from end to end. The spring perch bosses are 2 1/4 inches. 1932 axles were the first Ford axles to be made with a slight drop. These axles are often referred to as 1932 heavy axles. They are unique among early Ford axles in having a wider recess at the ends, and a slightly raised area on the front …your rear axle looks to have a 1943 date....it is on the little round "doughnut" to the right of the diff cover... sometimes the fronts had a ...Ford Rear Axle Assembly Identification - Page 17. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.Pinion Yoke and ABS Plug. 8) These rearends generally use a 28-spline pinion yoke, but some trucks use a 30-spline. 9) This is the plug for ABS found on some 8.8s. Advertisement. The Ford 8.8... Ford Rear Axle Assembly Identification - Page 04. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L. Axle Shaft Splines. Additional Information. Ratio. While some parts carried over from 2010, most 2011-up 10-1/2" Ford rear axle parts are not interchangeable with 2010 and older axle. Ford 10.5" full-floating rear axles were the only available axle for 2000-2005 Excursions plus 1999-2016 Ford F-250 and Single Rear Wheel (SRW) F-350 trucks. A Dual Rear Wheel Version (DRW) was also used for some ...60-63 falcon - tiny six cylinder rear end, four lug. 63 v8 8" rear end five lug - collectable since it fits the 60-63 cars. desierable for v8 conversions. since you don't have to mess with moving the spring perches. 64 v8 five lug - don't know off hand but i bet they're 8". oh, and if it is a v8 the frame mounts and intermediate mounts that go ...

1113 posts · Joined 2006. #2 · Jan 31, 2010. You have an 8.8.You could swap in a ford 9''.Just make sure you get one with the same gear ratio as your old one so it matches the front.The most common ratio was 3.55 for a 8.8 and 3.50 for a 9'' in a Bronco.An axle from a f150 would bolt in as well. Custom front and rear bumpers.Identifying The 7.5-Inch 10-Bolt. Although the 7.5-inch 10-bolt closely resembles the 8.5-inch housing, you can positively identify the Chevy 7.5-inch rearend by measuring it. The oval-shaped cover measures 8 5/16 inches by 10 9/16 inches. The distance between the bottom center bolt in the cover and its adjacent bolts is 3 1/4 inches.So I picked up this rear end the yesterday. The seller told me he thought it was a 38, the underside of the banjo is marked 9 40 so I believe it is a 4.44 to 1 ratio. What I am really having trouble identifying is the brakes that are on it. Here are a few pick hopefully someone can help.Dec 3, 2023 · One of the vital factors in identifying the 8 inch rear end is knowing the gear ratios that were available. The gear ratios ranged from around 2.79:1 to 4.13:1, with many variations in between. These ratios will determine the vehicle’s acceleration, top speed, and fuel efficiency. For those looking to modify their 8-inch differential ... Instagram:https://instagram. bourbon county detention center paris kentuckydiaper girl captionlennox 5 ton ac unitk.i stl ID Tags: The Ford 8.8 differential ID tag attached to the differential will tell you the gear ratio, rear end style, and whether it has limited-slip. Also on the tag is an ID number, which, until 1985, included four to five letters and no numbers. Almost all 8.8s – and all post-’86 Ford rear ends – have letters and numbers.The Mustang came from the factory with a 7.5-inch or 8.8-inch rear end, after 1979, with a variety of gear ratios and in both limited slip and open differential configurations. Decoding the data tag on the rear end will provide the information required when ordering replacement or up-graded parts for the Ford differential inside the rear end ... gun range in stone mountain gadoordash commercial with matty matheson rear end identification Early V8 (1932-53) The Ford Barn. FordBarn.com; The Forum; Swap; About; Register; Calendar; Community; Today's Posts; Search; FAQ : The Ford Barn > General Discussion > Early V8 (1932-53) rear end identification User Name: Remember Me? Password ...Lincoln Mark Series 72. 3.00. 9 3/8. NL. 31. full round flange. WGB-AA. Lincoln Mark Series 76-77. Thunderbird 76. honeywell home pro series flashing cool on Step 1 - Locate the Axle Code. To find the axle code: 1. View the Safety Compliance Certification Label on the driver's side, front or rear door panel. 2. Find the word "AXLE" under the bar code. 3. Find the two-digit code under "AXLE." Step 2 - Find the Axle Ratio. To locate the axle ratio after you have found the axle code:Ford Rear Axle Assembly Identification - Page 02. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.A few ways to tell a the difference between a Ford 9" rear end and a Ford 8" rear end. The main way to tell is the 3rd member is flat on top on a Ford 8 inc...